BMW Hidden Features 2 Series F44 Gran Coupe
BMW 2 Series F44 Gran Coupe(2020+)
Checkbox acoustic pedestrian protection
Enable/disable the checkbox in the settings in the iDrive system to turn the acoustic pedestrian protection on or off.
Values:
- Active
- Not active
Checkbox acoustical lock confirmation
Enable/disable the checkbox in the settings for doors/keys in the iDrive system to enable/disable the acoustical lock confirmation. If the checkbox in the iDrive system does not allow selection, please check if “Acoustical lock/unlock confirmation” in the “Roof Function Center” control unit is set to “Active“ also. Please note that the car has to be equipped with an alarm system.
Values:
- Active
- Not active
Active Sound Design
Enable/disable the Active Sound Design. Please note that it is not possible to enable the Active Sound Design for cars that are not equipped with this option by factory.
Values:
- Active
- Not active
AC on in air recirculation mode
Turn on the AC when activating the air recirculation mode.
Values:
- Active
- Not active
Air circulation setting memory
Enable/disable storing of the air circulation setting. If this function is active, the last used air circulation setting will be restored during the next start of the car.
Values:
- Active
- Not active
Apply AUTO settings to manual mode
Apply the AUTO settings when switching from the AUTO mode to the manual mode.
Values:
- Active
- Not active
Automatic Air Recirculation
Enable/disable the Automatic Air Recirculation function.
Values:
- Active
- Not active
Bowers & Wilkins sound settings
With the Bowers & Wilkins sound settings, extended sound presets are activated in the settings in the iDrive system under “Sound“. Please note that these only have an effect if a Harman Kardon sound system is installed in the vehicle. Use a backup to revert this coding once it has been applied.
Values:
- Active
Maximum volume at start-up
The maximum volume that is saved when the iDrive system is shut off and restored automatically on the next start-up.
Values:
- 10%
- 20%
- 25%
- 30%
- 40%
- 50%
Ringtone
The ringtone that is used in case of an incoming call.
Values:
- BMW i ringtone
- BMW ringtone
- Mini ringtone
- Smartphone ringtone
Warning chime
The warning chime that sounds when a warning is displayed in the car.
Values:
- BMW i warning chime
- BMW warning chime
- Mini warning chime
- Rolls Royce warning chime
Auto Start Stop function
Enable/disable the Auto Start Stop function.
Values:
- Active
- Not active
Auto Start Stop function memory
Save the last used Auto Start Stop function setting for the next start of the car. Please note that the Auto Start Stop function is automatically activated again in ECO PRO driving mode.
Values:
- Active
- Not active
Battery capacity
The capacity of the 12 V battery. Please note that this value must only be modified if the battery in the car has been replaced. After coding, the battery replacement has to be registered using “BimmerLink” additionally.
Values:
- 20 Ah
- 50 Ah
- 60 Ah
- 69 Ah
- 70 Ah
- 80 Ah
- 90 Ah
- 105 Ah
Battery type
The type of the 12 V battery. Please note that this value must only be modified if the battery in the car has been replaced. After coding, the battery replacement has to be registered using “BimmerLink” additionally.
Values:
- AGM
- EFB
- Lead acid
- Lithium-ion
Brake Force Display activation brake force
The brake deceleration at which the Brake Force Display is activated.
Values:
- Weak braking (5 m/s²)
- Medium braking (7 m/s²)
- Hard braking (8 m/s²)
Brake Force Display activation speed
The speed at which the Brake Force Display is activated.
Values:
- 5 km/h
- 10 km/h
- 20 km/h
- 30 km/h
- 40 km/h
- 50 km/h
CarPlay fullscreen mode
Show CarPlay in full screen mode. Important: This coding only works with the iDrive software versions “NBTevo_X“ and “NBTevo_Y“. You can easily check for yourself which software version is currently installed in your vehicle. To do this, navigate to the version info in the iDrive system in your vehicle (Navigation > Settings > Position and version > Version information). If you can see “NBTevo_X“ or “NBTevo_X“ here, then full screen mode will work. If you see “NBTevo_N“, “NBTevo_O“, “NBTevo_P“, “NBTevo_Q“, “NBTevo_R“, “NBTevo_S“, “NBTevo_U“, “NBTEvo_V“ or “NBTEvo_W“ instead, then full screen mode can not be enabled with BimmerCode unfortunately.
Values:
- Active
- Not active
Checkbox daytime running light
Enable/disable the checkbox in the lighting settings in the iDrive system to turn the daytime running light on or off.
Values:
- Active
- Not active
Cover Artwork
Values:
- Active
- Not active
Display full text messages
Enable the full display of text messages while driving. Use a backup to revert this coding once it has been applied.
Values:
- Active
Rear view camera zoom
Enable/disable the rear view camera zoom to the trailer hitch.
Values:
- Active
- Not active
Service history
Enable/disable the service history in the iDrive system.
Values:
- Active
- Not active
Start animation
The animation that is displayed when the iDrive system is started. Please note that the animation is not visible every time you start the car, but only under certain circumstances.
Values:
- Default
- BMW
- M variant 1
- ALPINA
- BMW i
- Rolls Royce
Start animation
The animation that is displayed when the iDrive system is started. Please note that the animation is not visible every time you start the car, but only under certain circumstances.
Values:
- ALPINA
- BMW i
- Connected Drive
- M variant 1
- M variant 2
- MINI John Cooper Works
- MINI variant 1
- MINI variant 2
- Rolls Royce
Start screen
The type of start screen that is displayed when the head unit starts up.
Values:
- Animation
- Welcome screen
Tire pressure control
The displayed values of the tire pressure control in the iDrive system. Please note that the car has to be equipped with the required sensors to make this work.
Values:
- Display pressure only
- Display temperature and pressure
- Not active
Volume popup
Enable/disable the volume popup that is displayed when the volume is changed.
Values:
- Active
- Not active
Average values reset
The average speed and consumption is reset after the set time automatically.
Values:
- After 4 hours
- After 8 hours
- After every ride
- Never
Diesel logo
Enable/disable the Diesel logo.
Values:
- Active
- Not active
Digital speed in board computer
Enable/disable the display of the digital speed in the board computer. Please toggle the displayed information in the board computer with the button in the turn signal lever until the specific display appears.
Values:
- Active
- Not active
Empty menu item in board computer
Enable/disable the empty menu item in the board computer.
Values:
- Active
- Not active
Fuel consumption display maximum value
The maximum value of the fuel consumption display.
Values:
- 15 l/100km
- 20 l/100km
- 30 l/100km
Layout
Change of layout in the instrument cluster.
Values:
- ALPINA
- M
- M Performance up to 160 mph
- M Performance up to 200 mph
- M Sport
- Standard
M Performance logo
The model-specific M Performance logo that is displayed in the bottom right in the instrument cluster.
Values:
- Not active
- 135i
- 140i
- 235i
- 240i
- 340i
- 50d
- 550d
- Plugin Hybrid Electric Vehicle
- X2 M40i
Refresh rate digital speed
The refresh rate for the digital speed display in the instrument cluster.
Values:
- 2 times per second
- 5 times per second
Start logo
The logo that is displayed in the center of the screen during the start-up of the instrument cluster.
Values:
- 50d
- 135i
- 140i
- 235i
- 240i
- 340i
- AG
- M Performance
- M2
- M2 Competition
- M2 CS
- M3
- M4
- M4 GTS
- Plugin Hybrid Electric Vehicle
- X2 M35i
Horn signal when locking the car with engine running
Enable/disable the horn signal that sounds when locking the car with the engine running.
Values:
- Active
- Not active
Time until automatic lock
The car is locked automatically again if it has been unlocked and no door has been opened within the set time.
Values:
- 10 seconds
- 30 seconds
- 1 minute
- 2 minutes
- 5 minutes
- 10 minutes
Window lifter interruption when opening a door
Enable/disable the window lifter interruption when a door is opened.
Values:
- Active
- Not active
Default driving mode
Values:
- ADAPTIVE
- COMFORT
- COMFORT INDIVIDUAL
- COMFORT+
- ECO PRO
- ECO PRO INDIVIDUAL
- ECO PRO+
- SPORT
- SPORT INDIVIDUAL
Low fuel warning 1
The remaining range at which the permanent low fuel warning is displayed.
Values:
- 10 kilometers
- 10 miles
- 20 kilometers
- 20 miles
- 30 kilometers
- 30 miles
- 40 kilometers
- 50 kilometers
- Not active
Low fuel warning 2
The remaining range at which the temporary low fuel warning is displayed.
Values:
- 40 miles
- 50 kilometers
- 50 miles
- 60 kilometers
- 70 kilometers
- 80 kilometers
- 90 kilometers
- Not active
Automatic light control
The lighting switch position where the automatic light control is active. To prevent the low beam to come on when the switch is set to “0”, use the option “Active in position A”.
Values:
- Active in position A
- Active in position A and 0
Exterior lighting switch-off allowed
Allow the exterior lights to be turned off when the engine is running.
Values:
- Active
- Not active
Fog lights off with high beam
Enable/disable the automatic switch-off of the fog lights when the high beam is turned on.
Values:
- Active
- Not active
Fog lights with parking lights
Allows the fog lights to be turned on with parking lights.
Values:
- Active
- Not active
Hazard warning signal after emergency braking
The hazard warning signal is activated automatically after an emergency braking.
Values:
- Active
- Not active
Rain-light-sensor sensitivity
The sensitivity of the rain-light-sensor that affects the automatic wiper and light activation.
Values:
- Insensitive
- Normal
- Sensititve
- Very sensitive
Automatic mirror tilt
Enable/disable the automatic mirror tilt for the right mirror, when the reverse gear is engaged. Please note that your car has to be equipped with power folding mirrors. Make sure the button in the door for selecting the mirror is set to the driver side also.
Values:
- Active
- Not active
Automatic mirror tilt value
The tilt value of the right mirror, when the reverse gear is engaged.
Values:
- 10%
- 20%
- 30%
- 40%
- 50%
- 60%
- 70%
- 80%
- 90%
- 100%
Fold mirrors with convenient closing
Enable/disable the folding of the mirrors when using convenient closing. Please note that your car has to be equipped with power folding mirrors and that this option does not work for convertibles.
Values:
- Active
- Not active
Unfold mirrors with convenient opening
Enable/disable the unfolding of the mirrors when using convenient opening.
Values:
- Active
- Not active
One-touch turn signal 5 times
Enable/disable the “5 times” one-touch turn signal option in the exterior lighting settings in the iDrive system.
Values:
- Active
- Not active
PDC/Top View distance switch-off threshold
The driven distance after the PDC is turned off automatically.
Values:
- 10 m
- 20 m
- 30 m
- 40 m
- 50 m
- 100 m
- 150 m
- 200 m
- 250 m
PDC/Top View speed switch-off threshold
The speed at which the PDC and the Top View is turned off automatically.
Values:
- 5 km/h
- 10 km/h
- 15 km/h
- 20 km/h
- 30 km/h
- 35 km/h
- 40 km/h
- 50 km/h
Rear view camera distance switch-off threshold
The driven distance after the rear view camera is turned off automatically.
Values:
- 10 m
- 20 m
- 30 m
- 40 m
- 50 m
- 100 m
- 150 m
- 200 m
- 250 m
Rear view camera speed switch-off threshold
The speed at which the rear view camera is turned off automatically.
Values:
- 5 km/h
- 10 km/h
- 15 km/h
- 20 km/h
- 30 km/h
- 36 km/h
- 40 km/h
- 50 km/h
Front backrests temperature level 1
The temperature of the front backrests for seat heating level 1.
Values:
- 30 °C
- 31 °C
- 32 °C
- 33 °C
- 34 °C
- 35 °C
Front backrests temperature level 2
The temperature of the front backrests for seat heating level 2.
Values:
- 36 °C
- 37 °C
- 38 °C
- 39 °C
- 40 °C
- 41 °C
Front backrests temperature level 3
The temperature of the front backrests for seat heating level 3.
Values:
- 42 °C
- 43 °C
- 44 °C
- 45 °C
- 46 °C
- 47 °C
Front seats temperature level 1
The temperature of the front seats for seat heating level 1.
Values:
- 30 °C
- 31 °C
- 32 °C
- 33 °C
- 34 °C
- 35 °C
Front seats temperature level 2
The temperature of the front seats for seat heating level 2.
Values:
- 36 °C
- 37 °C
- 38 °C
- 39 °C
- 40 °C
Front seats temperature level 3
The temperature of the front seats for seat heating level 3.
Values:
- 41 °C
- 42 °C
- 43 °C
- 44 °C
- 45 °C
- 46 °C
- 47 °C
- 48 °C
- 49 °C
- 50 °C
Rear backrests temperature level 1
The temperature of the rear backrests for seat heating level 1.
Values:
- 30 °C
- 31 °C
- 32 °C
- 33 °C
- 34 °C
- 35 °C
Rear backrests temperature level 2
The temperature of the rear backrests for seat heating level 2.
Values:
- 36 °C
- 37 °C
- 38 °C
- 39 °C
- 40 °C
- 41 °C
Rear backrests temperature level 3
The temperature of the rear backrests for seat heating level 3.
Values:
- 42 °C
- 43 °C
- 44 °C
- 45 °C
- 46 °C
- 47 °C
Rear seats temperature level 1
The temperature of the rear seats for seat heating level 1.
Values:
- 30 °C
- 31 °C
- 32 °C
- 33 °C
- 34 °C
- 35 °C
- 36 °C
Rear seats temperature level 2
The temperature of the rear seats for seat heating level 2.
Values:
- 35 °C
- 36 °C
- 37 °C
- 38 °C
- 39 °C
- 40 °C
Rear seats temperature level 3
The temperature of the rear seats for seat heating level 3.
Values:
- 40 °C
- 41 °C
- 42 °C
- 43 °C
- 44 °C
- 45 °C
- 46 °C
- 47 °C
- 48 °C
- 49 °C
Seat heating/cooling setting memory
The memory duration of the seat heating/cooling settings.
Values:
- 15 minutes
- 24 hours
- Do not save
- Unlimited
Initial seat belt reminder after start
Activate/deactivate the initial acoustic seat belt reminder after the car is started.
Values:
- Active
- Not active
Seat belt indicator driver seat
Activate/deactivate the seat belt indicator in the instrument cluster for the driver seat.
Values:
- Active
- Not active
Seat belt indicator passenger seat
Activate/deactivate the seat belt indicator in the instrument cluster for the passenger seat.
Values:
- Active
- Not active
Seat belt reminder driver seat
Activate/deactivate the acoustic and visual seat belt reminder for the driver seat.
Values:
- Active
- Not active
Seat belt reminder passenger seat
Activate/deactivate the acoustic and visual seat belt reminder for the passenger seat.
Values:
- Active
- Not active
G-Meter maximum value
The maximum value displayed in the G-meter for scaling.
Values:
- 0.8 g
- 0.9 g
- 1.0 g
- 1.2 g
- 1.5 g
- 1.8 g
- 2.0 g
Sport displays
Enable/disable the Sport displays in the iDrive system. Please note that in some cars the engine control unit does not transmit the required values to the headunit and in this case the Sport displays will be displayed but remain functionless.
Values:
- Active
- Not active
Sport displays color
The color of the Sport displays in the iDrive system.
Values:
- Orange
- Red
Sport displays values
The values shown in the sports displays. Please note that, depending on the vehicle, not all displays may work.
Values:
- G-meter, power, torque, oil temperature, boost pressure
- Not active
- Power, torque
Boot lid opening delay
The delay when opening the boot lid with the remote control. This value can be increased to prevent accidental openings of the boot lid.
Values:
- 0.5 seconds
- 0.7 seconds
- 1 second
- 2 seconds
- 3 seconds
- 4 seconds
- 5 seconds
- 10 seconds
- No delay
Open tailgate after unlock only
The tailgate can only be opened after unlocking the car with the remote control. Please note that “Tailgate“ has to be selected for the tailgate button in the settings in the iDrive system in the car.
Values:
- Active
- Not active
Additional video codecs and formats
Activate additional video codecs and formats (Ogg, Xvid and VCD). Use a backup to revert this coding once it has been applied.
Values:
- Active
Video in motion
Enable video in motion. Please note the instructions displayed after coding.
Values:
- Active
- Not active
Video via USB
Enable video playback from USB storage media. Use a backup to revert this coding once it has been applied.
Values:
- Active
- Not active
Camera warning
Disable the warning that is displayed when using one of the cameras. Use a backup to revert this coding once it has been applied.
Values:
- Not active
Night vision warning
Disable the warning that is displayed when using the night vision camera. Use a backup to revert this coding once it has been applied.
Values:
- Not active
Warning at start-up
Disable the warning that is displayed when the iDrive system is started. Use a backup to revert this coding once it has been applied.
Values:
- Not active
Welcome Light in darkness only
Enable/disable the activation of the Welcome light in darkness only.
Values:
- Active
- Not active
